IC693ALG442 Output Transient Mitigation: Hardware Delay Relay Strategy for 10V Pulse Suppression at CPU Power Loss
Industrial automation engineers often face hidden risks when a PLC rack loses power. The GE Fanuc Series 90-30 IC693ALG442 analog combination module can produce an unexpected voltage spike on its output channels during CPU power-down events. This article explains the root cause, proposes a hardware delay relay solution, and provides practical timing calculations, wiring logic, and component selection guidance for factory automation professionals.
Why Does the 10V Pulse Appear on the IC693ALG442 Output?
The IC693ALG442 module draws power from two separate sources. Logic power comes from the backplane +5V rail. The analog output loop, however, needs an external user supply of 20 to 30 VDC. During a mains interruption, the CPU and backplane rails collapse quickly. In contrast, the external user supply may hold energy for a longer period due to bulk capacitance. This asymmetry creates a window where the module’s internal DAC may interpret floating logic states as valid commands. As a result, a transient voltage can appear at the output terminals. The pulse magnitude approaches the full-scale range, typically 10V in unipolar mode. Field reports indicate this transient persists for several milliseconds. The exact duration depends on the discharge rate of the external 24V supply. Without mitigation, downstream actuators or variable frequency drives may register this pulse as a valid command. This behavior is particularly hazardous for proportional valves and positioners that respond to fast transients.
Timing Budget: Backplane Holdup vs. External Supply Decay
Published specifications for Series 90-30 power supplies indicate a minimum holdup time of 20 ms for the IC693PWR321 and IC693PWR330 under nominal input conditions. For the IC693PWR322, the minimum is 14 ms. These figures represent the time the backplane rails remain within regulation after input power loss. Conversely, the external 24V user supply feeding the ALG442 output loop may hold significantly longer. A typical industrial supply with 10,000 µF of bulk capacitance and a 200 mA load can maintain voltage for over 500 ms. This mismatch means the output stage remains “alive” while the digital logic has already lost control. The module’s configured behavior during power interruption—either Hold Last State or Reset to Low End—only applies if the backplane logic remains active to execute that command. Once the CPU loses authority, the output state becomes undefined. Therefore, the delay relay must act faster than the external supply decay but slower than legitimate control signals. A delay window of 50 to 150 ms suits most installations.
Hardware Implementation: Wiring the Delay-Off Relay in the Output Loop
Engineers insert the delay relay in series with the output loop’s common return path or the individual channel line. For voltage output mode, the relay contacts sit between the module’s output terminal and the field device’s positive input. The relay coil draws energy from the same external 24V supply that powers the module’s output loop. Critically, the coil must not draw power from the backplane +5V rail. When the external 24V supply collapses, the delay relay begins its timing cycle. A normally open (NO) contact configuration is mandatory. This ensures the output circuit physically breaks when the relay de-energizes. The delay period must exceed the maximum expected transient duration from the module but remain shorter than the response time of any safety-critical downstream system. For the IC693ALG442, a delay setting of 100 ms provides a 5:1 margin over the observed 20 ms transient window. The relay must handle the loop current and voltage. For 0 to 20 mA loops, a contact rating of 1 A at 30 VDC is sufficient. For voltage outputs up to ±10V, the same rating applies. Optocoupler-isolated relay modules are preferred to prevent ground loops between the external supply and the backplane.

Component Selection Criteria: Delay Range, Contact Material, and Environmental Ratings
Commercial delay-off relay modules suitable for this application must meet several specifications. First, the timing range must cover 0.1 to 10 seconds with repeatability better than ±5%. Modules based on RC timing circuits are adequate; microcontroller-based timers offer superior accuracy. Second, the relay contact must handle low-level signals. Gold-plated contacts are recommended for currents below 100 mA to prevent oxide buildup. For 4 to 20 mA loops, the contact resistance must remain stable below 100 mΩ over the product lifetime. Third, the module must tolerate the industrial electromagnetic environment. The Series 90-30 operates in enclosures with adjacent contactors and drives. A relay module with optocoupler isolation on the trigger input and a flyback diode across the coil is essential. Fourth, the operating temperature range must match the panel environment. Most industrial delay relays are rated for –20°C to 60°C, which aligns with the Series 90-30 enclosure rating. Finally, the module should feature a “power-off memory” or non-volatile timing setting. This prevents the delay setpoint from drifting after a power cycle. Products with a timing range of 0.01 seconds to 999 minutes are commercially available and provide ample adjustment margin.
Verification and Commissioning: Oscilloscope Checks and Failure Mode Testing
Commissioning requires verification of two parameters: transient suppression and normal signal integrity. A digital oscilloscope with a 10x probe connects directly across the field terminals of the ALG442 output channel. The timebase is set to 10 ms/div. The first test involves a controlled power-down of the CPU rack while the external 24V supply remains energized. Without the relay, a 10V pulse with a duration of approximately 5 to 15 ms should be observed. With the delay relay installed and set to 100 ms, the output should fall to zero within 2 ms of the relay de-energizing. The residual voltage should be less than 50 mV. The second test verifies normal operation. A step command from the PLC should produce an output transition that passes through the relay without measurable delay or distortion. The relay contact resistance should introduce less than 0.1% error in a 20 mA loop. A third test simulates a relay failure. If the relay contacts weld closed, the mitigation is lost. Therefore, periodic proof-testing of the relay is recommended in safety-related applications. For non-safety applications, the relay’s mechanical life of 100,000 operations or more is sufficient for infrequent power-down events. The final step is to document the delay setting on the panel and in the maintenance log. This ensures that replacement personnel do not inadvertently shorten the delay and reintroduce the transient risk.
Author Insight: Why Hardware Mitigation Still Matters in Modern Control Systems
Many engineers assume that modern PLC and DCS platforms have eliminated legacy transient issues. However, installed base equipment such as the GE Fanuc Series 90-30 remains widespread in factory automation and process control. Hardware-based mitigation offers deterministic behavior that firmware alone cannot guarantee. In my experience, a properly specified delay relay is a cost-effective safeguard for analog output loops. Moreover, it complements software configuration rather than replacing it. I recommend documenting the relay setting and including it in routine maintenance checks. This practice improves both reliability and audit readiness for industrial control systems.
Application Case: Protecting Proportional Valves in a Power-Down Scenario
A manufacturing line used an IC693ALG442 module to command proportional hydraulic valves. During plant shutdowns, operators noticed occasional valve movement. The movement occurred even though the PLC was commanded to reset outputs. An investigation revealed a 10V transient on the analog output during CPU power loss. The external 24V supply held voltage longer than the backplane holdup time. Engineers installed an optocoupler-isolated delay-off relay with a 100 ms setting in the output loop. The relay coil drew power from the external 24V supply. After commissioning, oscilloscope tests confirmed that the transient fell below 50 mV. Normal valve response remained unchanged. This solution improved safety and reduced unplanned actuator wear.

Frequently Asked Questions
What causes the 10V pulse on the IC693ALG442 output?
The pulse appears because the backplane logic rail collapses faster than the external 24V output supply. The module’s DAC may interpret floating logic states as valid commands. As a result, a transient voltage can reach the output terminals.
Can I fix this issue with PLC configuration alone?
Hold Last State or Reset to Low End settings only work while backplane logic remains active. Once the CPU loses authority, the output state becomes undefined. Therefore, hardware mitigation is often necessary for deterministic isolation.
What delay setting is recommended for the delay relay?
A delay window of 50 to 150 ms suits most installations. For the IC693ALG442, a 100 ms setting provides a 5:1 margin over the observed 20 ms transient window.
Which relay contact material suits low-level analog signals?
Gold-plated contacts are recommended for currents below 100 mA. They prevent oxide buildup and help maintain stable contact resistance below 100 mΩ in 4 to 20 mA loops.
How do I verify that the mitigation works?
Use a digital oscilloscope with a 10x probe across the field terminals. Perform a controlled CPU power-down while the external 24V supply remains energized. With the relay installed, the output should fall to zero within 2 ms and stay below 50 mV.



